Recessed Low Voltage Cable Plate · 1-Gang · White Pass-Through · Cable Concepts Datacomm WPCD0002
1-gang recessed low voltage cable plate for routing AV, data, coaxial and speaker cabling through finished walls with a cleaner, flush-looking exit point. Commonly used behind wall-mounted TVs and structured cabling terminations; actual cable capacity depends on connector size, bend radius and wall opening.
What this product is for
This recessed low voltage cable plate is used to pass low voltage cabling through a finished wall while keeping the cable exit set back from the wall surface. It is suited to HDMI, Ethernet, coaxial, speaker wire and similar communications or AV cabling where a standard open hole or flat plate would leave connectors protruding too far.
Use for
- Wall-mounted TV and display cabling
- Home theatre and AV equipment connections
- Structured cabling pass-through points
- Low voltage cable routing in new work or retrofit applications
- Single-gang low voltage openings
Avoid for
- Line-voltage power terminations
- Applications requiring listed data, coaxial or audio connectors on the faceplate
- Installations where cable protection, firestopping or code requirements call for a different fitting
Best for
Best for electricians, low voltage installers and AV contractors who need a cleaner cable exit behind flat-panel displays, amplifiers or media equipment. A recessed opening typically helps reduce connector strain and allows equipment to sit closer to the wall than a non-recessed pass-through plate.
Installed in
Typically installed in a standard 1-gang low voltage mounting bracket or wall opening in finished residential or light commercial interiors. Common locations include media walls, boardrooms, offices, classrooms and residential entertainment areas.
Why this product exists
This product provides a neater alternative to leaving loose low voltage cables through drywall. It helps organize cable exits, improves the finished appearance and can make it easier to position connected equipment close to the wall.
Compared with similar products
Compared with a flat brush plate or open pass-through, a recessed cable plate gives more connector clearance behind displays and equipment. Compared with a connectorized wall plate, it is better when cable ends need to pass through without termination. Typical selection guidance: choose a recessed pass-through when connector bulk and wall clearance matter more than having fixed ports on the plate.
Actual cable fit depends on connector size, bend radius, cable bundle thickness and installation conditions.
Specifications
- Product type: Recessed low voltage cable plate
- Gang size: 1-gang
- Colour: White
- Application: Low voltage cable pass-through
- Typical cable types: HDMI, Ethernet, coaxial, speaker wire and similar low voltage cabling
- Mounting: Standard 1-gang low voltage opening
- Material: Plastic
- Use environment: Indoor dry location applications
Minimum Order $20
We accept the following payment methods:
Credit Card can offer cardholders convenience, security, rewards, and the opportunity to build a healthy credit history.
Click here for Contractor Cash Account
Trade Credit is a standard financing option for contractors and construction companies to obtain supplies and keep their projects moving. We offer 30-day credit terms to trade contractors on approved applications only.
Click here for Contractor Credit Account 
(Contractor Accounts)
Standard Shipping-Free on orders over $249 in Metropolitan Areas / $499 in Rural Areas
(All Other Accounts)
Standard Shipping-Free on orders over $499
Minimum Order Is $20
Freight Surcharge Apply To Oversized/Over-Weight Items(Not Limited To):
- PVC and EMT Pipe
- Wire and Cable
- Items over 48 inches in length
Surcharges are applied to items on an individual basis regardless if the rest of the order meets prepaid levels. If a freight line appears at the time of check out it only applies to the Items carrying a surcharge and not the entire basket of goods.
Shipping Options:
- A courier can deliver to your home, office, or your job site
- Pick up at local depot near you (applies to the following locations)
Edmonton Warehouse 8135 Roper Rd Edmonton, T6E 6S4, AB
Burnaby Warehouse 5608 Goring St Burnaby, V5B 3A3, BC
Orders are typically delivered within two to eleven business days. The transit time begins the first full shipping day after your order leaves our warehouse. Please allow an additional 2-5 days for delivery to remote locations, additional fees may apply.
THE FOLLOWING APPLIES TO STANDARD SHIPPING OPTIONS
- We cannot deliver to P.O. boxes.
- A signature may be required for shipments over $500.
- No weekend delivery.
- Wire & cable, EMT or PVC conduit, tube lamps 4ft or greater, and 10ft ground rods & mast pipes have special conditions.
Standard Shipping cost on orders less than $499
Total shipping cost = "Per Shipment" cost + "Per Item" cost. The "per item" cost is listed in terms of price per pound.
Product Group | Per Shipment* | Per Item |
|---|---|---|
Boxes | $6.99 | $1.49/lb |
Conduit & Raceway | $149.99 | $2.49/lb |
Connectors & Fittings | $5.99 | $1.19/lb |
Data & Structured Home | $5.99 | $1.19/lb |
Distribution Equipment | $5.99 | $1.19/lb |
Emergency Lighting | $6.99 | $1.49/lb |
Heating & Ventilation | $6.99 | $1.49/lb |
Lighting Controls | $5.99 | $1.19/lb |
Lighting Indoor | $6.99 | $1.49/lb |
Lighting Outdoor | $6.99 | $1.49/lb |
Tools | $4.99 | $.99/lb |
Wire & Cable | $49.99 | $2.29/lb |
Wiring Devices | $5.99 | $1.19/lb |
Any combination of the above items | Highest applicable per-shipment charge | As above |
Effective Date: August, 15, 1998
At Evolt Electrical Supply, customer satisfaction is our top priority. Please review our return policy below:
Returns
Defective Items:
- If you receive a defective item, you may return it for a replacement or refund within 30 days of purchase.
- To initiate a return, please contact our customer service team with your order number and a description of the defect.
Non-Defective Items:
- We do not accept returns for non-defective items. All sales are final once the product is shipped or ordered from the manufacturer. In certain circumstances we may amend this so feel free to contact our customer service team.
Return Process
Authorization:
- Before returning any items, you must obtain a Return Merchandise Authorization (RMA) number from our customer service team. Returns without an RMA number will not be accepted.
- Backordered items can not be cancelled if the item is in transit from the manufacturer, contact us to review.
Shipping:
- Customers are responsible for the return shipping costs. We recommend using a trackable shipping service or purchasing shipping insurance.
Condition:
- Returned items must be in their original packaging and condition. Any items returned damaged due to improper packaging or misuse will not be eligible for a refund or replacement.
Refunds
- Once we receive and inspect your returned item, we will notify you of the approval or rejection of your refund.
- Approved refunds will be processed within [7] business days and a credit will automatically be applied to your original method of payment.
