Slimline single-element infrared heater · 1600W 120V 29.5 in · Bronze anodized aluminium housing · Infratech SL-1612-BR

What this product is for

The Infratech SL-1612-BR is a slimline single-element electric infrared heater designed for targeted radiant heat in outdoor and indoor surface-mount applications. It is commonly used where you need focused warmth instead of heating a full room volume, such as patios, seating areas, entry points, workstations, and covered commercial outdoor spaces.

Use for

Use for small patio zones, condo balconies where permitted, restaurant waiting or seating areas, covered terraces, garages, workshops, and other locations needing directional comfort heat. This 120V, 1600W model draws approximately 13.3A, making it relevant where a 120V supply is preferred and the load is planned correctly for the branch circuit.

Typical guidance: this model is often used for approximately 25 sq ft (about 5 x 5 ft / 1.5 x 1.5 m) of spot-heating coverage when mounted and aimed correctly. Actual performance depends on mounting height, wind exposure, ambient temperature, layout, and local electrical code.

Avoid for

Avoid using this heater where broad-area space heating is expected, in highly exposed windy locations without accounting for heat loss, or where the branch circuit does not have adequate capacity. It is not the right choice when you need whole-room heating or thermostat-style air heating.

Best for

Best for electricians, contractors, and property owners specifying a low-profile radiant heater for smaller zones. It suits projects where appearance matters, where a bronze finish is preferred, and where direct infrared heat is more practical than forced-air heating.

Installed in

Typically installed on exterior walls, under covered patios, pergolas, restaurant canopies, workshop walls, and similar mounting surfaces. Manufacturer reference material lists the SL-Series for outdoor surface-mount applications, with this 29.5 in (749 mm) model commonly mounted around 6 to 8 ft (1.8 to 2.4 m) high and adjustable through a 0 to 60 degree mounting angle, depending on the bracket setup and site design.

Why this product exists

This heater exists for projects that need compact, directional radiant heat from a slim housing rather than a larger dual-element unit. Compared with higher-wattage patio heaters, it fits tighter spaces and smaller heating zones while still delivering the fast-response comfort associated with quartz infrared heating.

Trade note: on a 120V circuit, a 1600W heater is approximately 13.3A. As a rule of thumb, continuous loads are typically limited to 80% of breaker rating, so circuit planning matters before specifying controls and branch wiring. Actual installation requirements depend on the complete load calculation and applicable code.

Compared with similar products

Compared with larger SL-Series models, the SL-1612-BR is the shortest and lowest-wattage option in the family, making it better suited to smaller seating or standing areas. Compared with 240V versions of similar wattage, this 120V model can be easier to place where only 120V power is available, but it still requires proper load consideration because of its current draw.

The bronze version adds a bronze body with stainless steel trim relative to the standard stainless finish model designation.

Specifications

• Manufacturer: Infratech
• Manufacturer part number: SL-1612-BR
• Series: SL-Series Slimline
• Heater type: Single-element quartz infrared radiant heater
• Input voltage: 120V
• Wattage: 1600W
• Current draw: 13.3A
• Length: 29.5 in (749 mm)
• Finish: Bronze body with stainless steel trim
• Housing material: Anodized aluminium housing
• Application: Residential and commercial
• Mounting: Surface mount, adjustable angle approximately 0 to 60 degrees
• Typical mounting height: 6 to 8 ft (1.8 to 2.4 m)
• Typical coverage guidance: approximately 25 sq ft (2.3 sq m)
• Ingress rating: IPX4
• Use location: Indoor or outdoor locations as permitted by manufacturer instructions and code