Flush Mount Duplex Stack Switch Assembly · Weatherproof Cover · 20A Max · Infratech 14-4310
What this product is for
This flush-mount duplex stack switch assembly is used to control compatible Infratech dual-element radiant heaters in outdoor or exposed locations where a weatherproof cover is required. It combines a steel gang box, stainless cover, and stacked switch arrangement in one assembly.
Use for
Use for Infratech dual-element CD-Series and WD-Series heaters where independent switching of each element is needed. This setup is commonly used to give electricians and end users simple on/off control with effective half-power or full-power operation, depending on which elements are energized.
Avoid for
Avoid using this assembly for single-element heater applications, for loads exceeding 20A per switch, or where a different control strategy such as infinite control or timer-based control is required. Confirm heater compatibility and local code requirements before ordering.
Best for
Best for outdoor patio heater installations in residential and light commercial settings where a clean flush finish and weather-resistant cover are important. It suits projects that need straightforward manual control without moving to more advanced custom control packages.
Installed in
Typically installed in exterior walls, outdoor kitchens, covered patios, restaurant patio heating zones, and similar exposed areas. Assembly size is approximately 4.38 x 2.63 x 1.88 in. (111 x 67 x 48 mm), which helps when planning wall depth and cover clearance.
Why this product exists
Infratech offers this assembly to provide a ready-made flush-mount switching option for dual-element heaters in locations that need weather protection. It simplifies product selection compared with sourcing separate box, cover, and switch components.
Compared with similar products
Compared with surface-mount switch assemblies, this flush-mount version gives a more built-in appearance. Compared with non-weatherproof versions, the included weatherproof cover is better suited to outdoor installations. Compared with more advanced control systems, this is a simpler manual switching option with fewer programming requirements.
Typical guidance only: independent element switching is commonly used to give more practical heat control in patio zones, but actual comfort and heater output depend on heater model, mounting height, exposure, and site conditions.
Specifications
- Manufacturer: Infratech
- Manufacturer part number: 14-4310
- Product type: Single flush-mount duplex stack switch assembly with weatherproof cover
- Application: Control accessory for compatible Infratech dual-element radiant heaters
- Compatible heater series: CD-Series and WD-Series dual-element heaters
- Electrical rating: 120 to 277 VAC
- Maximum rating: 20A per switch
- Control function: Independent element switching for effective half-power/full-power operation
- Mounting style: Flush mount
- Cover type: Weatherproof
- Approximate dimensions: 4.38 x 2.63 x 1.88 in. (111 x 67 x 48 mm)
- Materials: Steel J-box, stainless cover, plastic switch body
- Finish/colour: Stainless steel
- Country of manufacture: USA
Minimum Order $20
We accept the following payment methods:
Credit Card can offer cardholders convenience, security, rewards, and the opportunity to build a healthy credit history.
Click here for Contractor Cash Account
Trade Credit is a standard financing option for contractors and construction companies to obtain supplies and keep their projects moving. We offer 30-day credit terms to trade contractors on approved applications only.
Click here for Contractor Credit Account 
(Contractor Accounts)
Standard Shipping-Free on orders over $249 in Metropolitan Areas / $499 in Rural Areas
(All Other Accounts)
Standard Shipping-Free on orders over $499
Minimum Order Is $20
Freight Surcharge Apply To Oversized/Over-Weight Items(Not Limited To):
- PVC and EMT Pipe
- Wire and Cable
- Items over 48 inches in length
Surcharges are applied to items on an individual basis regardless if the rest of the order meets prepaid levels. If a freight line appears at the time of check out it only applies to the Items carrying a surcharge and not the entire basket of goods.
Shipping Options:
- A courier can deliver to your home, office, or your job site
- Pick up at local depot near you (applies to the following locations)
Edmonton Warehouse 8135 Roper Rd Edmonton, T6E 6S4, AB
Burnaby Warehouse 5608 Goring St Burnaby, V5B 3A3, BC
Orders are typically delivered within two to eleven business days. The transit time begins the first full shipping day after your order leaves our warehouse. Please allow an additional 2-5 days for delivery to remote locations, additional fees may apply.
THE FOLLOWING APPLIES TO STANDARD SHIPPING OPTIONS
- We cannot deliver to P.O. boxes.
- A signature may be required for shipments over $500.
- No weekend delivery.
- Wire & cable, EMT or PVC conduit, tube lamps 4ft or greater, and 10ft ground rods & mast pipes have special conditions.
Standard Shipping cost on orders less than $499
Total shipping cost = "Per Shipment" cost + "Per Item" cost. The "per item" cost is listed in terms of price per pound.
Product Group | Per Shipment* | Per Item |
|---|---|---|
Boxes | $6.99 | $1.49/lb |
Conduit & Raceway | $149.99 | $2.49/lb |
Connectors & Fittings | $5.99 | $1.19/lb |
Data & Structured Home | $5.99 | $1.19/lb |
Distribution Equipment | $5.99 | $1.19/lb |
Emergency Lighting | $6.99 | $1.49/lb |
Heating & Ventilation | $6.99 | $1.49/lb |
Lighting Controls | $5.99 | $1.19/lb |
Lighting Indoor | $6.99 | $1.49/lb |
Lighting Outdoor | $6.99 | $1.49/lb |
Tools | $4.99 | $.99/lb |
Wire & Cable | $49.99 | $2.29/lb |
Wiring Devices | $5.99 | $1.19/lb |
Any combination of the above items | Highest applicable per-shipment charge | As above |
Effective Date: August, 15, 1998
At Evolt Electrical Supply, customer satisfaction is our top priority. Please review our return policy below:
Returns
Defective Items:
- If you receive a defective item, you may return it for a replacement or refund within 30 days of purchase.
- To initiate a return, please contact our customer service team with your order number and a description of the defect.
Non-Defective Items:
- We do not accept returns for non-defective items. All sales are final once the product is shipped or ordered from the manufacturer. In certain circumstances we may amend this so feel free to contact our customer service team.
Return Process
Authorization:
- Before returning any items, you must obtain a Return Merchandise Authorization (RMA) number from our customer service team. Returns without an RMA number will not be accepted.
- Backordered items can not be cancelled if the item is in transit from the manufacturer, contact us to review.
Shipping:
- Customers are responsible for the return shipping costs. We recommend using a trackable shipping service or purchasing shipping insurance.
Condition:
- Returned items must be in their original packaging and condition. Any items returned damaged due to improper packaging or misuse will not be eligible for a refund or replacement.
Refunds
- Once we receive and inspect your returned item, we will notify you of the approval or rejection of your refund.
- Approved refunds will be processed within [7] business days and a credit will automatically be applied to your original method of payment.