Dual Flush Mount Input Regulator · 240V · Weatherproof Cover · Infratech 14-4215
What this product is for
This dual flush mount input regulator assembly is used to control compatible Infratech 240V single-element infrared heaters in outdoor or exposed locations. It includes a weatherproof cover and gang box for installations where the control needs added protection from the elements.
Use for
Use for Infratech W-Series and Slimline Series single-element heaters up to 3000W where staged heat control is needed instead of simple on/off switching. It is commonly selected for patios, restaurant seating areas, covered outdoor amenity spaces, and similar radiant heating applications.
Avoid for
Avoid using this control with non-compatible heater series, line voltages other than 240V, or applications requiring a standard thermostat-style control. Do not assume compatibility with dual-element heaters unless the heater manufacturer documentation specifically allows it.
Best for
Best for contractors and electricians specifying Infratech outdoor heating controls where a flush-mounted appearance and weather-resistant cover are required. This style is useful when the control location is exposed and a cleaner finished look is preferred over a surface-mounted assembly.
Installed in
Typically installed in exterior walls, covered patios, outdoor kitchens, hospitality terraces, and other damp or exposed areas. The weatherproof cover dimensions published by a distributor are approximately 5-1/2 in H x 5-1/2 in W x 1-1/4 in D (about 140 x 140 x 32 mm), with a cover tab extending about 1/4 in (6 mm).
Why this product exists
This control gives installers a way to reduce heater output by cycling two compatible heaters on and off at regular intervals when not set to full power. That can help improve comfort in outdoor spaces where full output is not always needed. As typical guidance for radiant heater controls, the connected load must match the control rating and the heater voltage.
Actual performance depends on heater model, wiring layout, installation conditions, and local electrical code.
Compared with similar products
Compared with a basic on/off switch, this INF input regulator provides variable-style heat control by cycling output rather than only switching fully on or off. Compared with a surface-mount control assembly, this flush mount version is better suited where wall finish and appearance matter, while still providing a weatherproof cover for exposed exterior locations.
Specifications
- Manufacturer: Infratech
- Part number: 14-4215
- Product type: Dual flush mount INF input regulator assembly
- Voltage: 240V
- Heater compatibility: Single-element heaters up to 3000W
- Typical compatible series: Infratech W-Series and Slimline Series
- Mounting style: Flush mount
- Enclosure: Gang box with weatherproof cover
- Application: Exposed exterior locations / outdoor heater control
- Approximate cover size: 5-1/2 in x 5-1/2 in x 1-1/4 in (140 x 140 x 32 mm)
Minimum Order $20
We accept the following payment methods:
Credit Card can offer cardholders convenience, security, rewards, and the opportunity to build a healthy credit history.
Click here for Contractor Cash Account
Trade Credit is a standard financing option for contractors and construction companies to obtain supplies and keep their projects moving. We offer 30-day credit terms to trade contractors on approved applications only.
Click here for Contractor Credit Account 
(Contractor Accounts)
Standard Shipping-Free on orders over $249 in Metropolitan Areas / $499 in Rural Areas
(All Other Accounts)
Standard Shipping-Free on orders over $499
Minimum Order Is $20
Freight Surcharge Apply To Oversized/Over-Weight Items(Not Limited To):
- PVC and EMT Pipe
- Wire and Cable
- Items over 48 inches in length
Surcharges are applied to items on an individual basis regardless if the rest of the order meets prepaid levels. If a freight line appears at the time of check out it only applies to the Items carrying a surcharge and not the entire basket of goods.
Shipping Options:
- A courier can deliver to your home, office, or your job site
- Pick up at local depot near you (applies to the following locations)
Edmonton Warehouse 8135 Roper Rd Edmonton, T6E 6S4, AB
Burnaby Warehouse 5608 Goring St Burnaby, V5B 3A3, BC
Orders are typically delivered within two to eleven business days. The transit time begins the first full shipping day after your order leaves our warehouse. Please allow an additional 2-5 days for delivery to remote locations, additional fees may apply.
THE FOLLOWING APPLIES TO STANDARD SHIPPING OPTIONS
- We cannot deliver to P.O. boxes.
- A signature may be required for shipments over $500.
- No weekend delivery.
- Wire & cable, EMT or PVC conduit, tube lamps 4ft or greater, and 10ft ground rods & mast pipes have special conditions.
Standard Shipping cost on orders less than $499
Total shipping cost = "Per Shipment" cost + "Per Item" cost. The "per item" cost is listed in terms of price per pound.
Product Group | Per Shipment* | Per Item |
|---|---|---|
Boxes | $6.99 | $1.49/lb |
Conduit & Raceway | $149.99 | $2.49/lb |
Connectors & Fittings | $5.99 | $1.19/lb |
Data & Structured Home | $5.99 | $1.19/lb |
Distribution Equipment | $5.99 | $1.19/lb |
Emergency Lighting | $6.99 | $1.49/lb |
Heating & Ventilation | $6.99 | $1.49/lb |
Lighting Controls | $5.99 | $1.19/lb |
Lighting Indoor | $6.99 | $1.49/lb |
Lighting Outdoor | $6.99 | $1.49/lb |
Tools | $4.99 | $.99/lb |
Wire & Cable | $49.99 | $2.29/lb |
Wiring Devices | $5.99 | $1.19/lb |
Any combination of the above items | Highest applicable per-shipment charge | As above |
Effective Date: August, 15, 1998
At Evolt Electrical Supply, customer satisfaction is our top priority. Please review our return policy below:
Returns
Defective Items:
- If you receive a defective item, you may return it for a replacement or refund within 30 days of purchase.
- To initiate a return, please contact our customer service team with your order number and a description of the defect.
Non-Defective Items:
- We do not accept returns for non-defective items. All sales are final once the product is shipped or ordered from the manufacturer. In certain circumstances we may amend this so feel free to contact our customer service team.
Return Process
Authorization:
- Before returning any items, you must obtain a Return Merchandise Authorization (RMA) number from our customer service team. Returns without an RMA number will not be accepted.
- Backordered items can not be cancelled if the item is in transit from the manufacturer, contact us to review.
Shipping:
- Customers are responsible for the return shipping costs. We recommend using a trackable shipping service or purchasing shipping insurance.
Condition:
- Returned items must be in their original packaging and condition. Any items returned damaged due to improper packaging or misuse will not be eligible for a refund or replacement.
Refunds
- Once we receive and inspect your returned item, we will notify you of the approval or rejection of your refund.
- Approved refunds will be processed within [7] business days and a credit will automatically be applied to your original method of payment.