EK320RO2 Hydel Self Contained Meter Socket 120/240V 1 Phase 3 Wire 320A

Unfortunately these units are only available in a 4 Jaw at this time. I checked with the rep and he does not believe they will be offering these in a 5 jaw in the forseeable future. We suggest he 400 Amp CT4 Series

1️⃣ Load Side Lug Capacity & Connections
The Hydel EK320RO2 meter socket features two-hole lugs on the load side, each rated for up to 350MCM wire.
Since the load side lugs can accommodate two conductors, you should be able to run one set of conductors to the 200A panel and another to the 125A panel.
2️⃣ Wire Size Considerations
200A panel typically uses 250MCM or 3/0 Cu (copper) or 250MCM Al (aluminum).
125A panel typically uses 1/0 Cu or 2/0 Al.
If the lugs support two conductors per hole, then you can land both correctly sized wires for each subfeed in the same lug.
3️⃣ NEC/CEC Compliance & Utility Approval
Check your local utility (BC Hydro or equivalent) to confirm they allow two separate panel feeds from a 320A meter socket.
Ensure neutral and ground bonding is properly configured in the panels according to CEC/NEC regulations.
4️⃣ Alternative Option: Splitter Box
If the utility or inspector does not allow direct termination of both panels at the meter socket, you may need a 320A splitter box after the meter to split the load between the two panels.
Final Answer:
✅ Yes, it can work if:

The load side lugs support two conductors per hole (confirm manufacturer specs).
Your utility permits multiple subfeeds from a 320A meter socket.
The wire sizes match proper ampacity ratings per CEC/NEC.
⚠️ If the utility does not allow dual panel feeds directly, use a 320A splitter box.

The dual 200A lugs on the load side of the Hydel 320A Meter Socket provide flexibility for different electrical configurations, but BC Hydro’s requirement of one 200A and one 125A maximum is based on their utility service limitations and load balancing regulations. Here’s why:

1. Manufacturer vs. Utility Regulations
The meter socket is designed to handle up to 320A of continuous load and provides dual 200A lugs to accommodate different customer setups.
BC Hydro, however, sets its own maximum allowable load distribution for safety, transformer load management, and system efficiency.
2. Avoiding Overloading the Transformer
Utility companies regulate maximum service sizes to prevent overloading transformers and ensure balanced electrical distribution across their grid.
The 320A-rated meter socket is a self-contained metering solution, but BC Hydro limits the usable load to 325A total (200A + 125A) rather than the full 320A continuous capacity.
3. Compliance with BC Hydro Standards
Even if the socket has dual 200A lugs, only a combination that meets BC Hydro’s service regulations can be connected.
If an electrician were to install dual 200A breakers, BC Hydro may reject the installation or require modifications.
4. Flexibility for Other Installations
The dual 200A lug configuration allows for installations in other jurisdictions or setups where higher load splits are allowed.
In areas outside of BC Hydro’s jurisdiction, two 200A breakers may be acceptable.
Key Takeaway:
The Hydel meter socket supports up to 320A, but BC Hydro limits the usable load to one 200A breaker and one 125A breaker to comply with their grid management standards.
The dual 200A lugs exist for flexibility in different jurisdictions, but the actual allowed configuration depends on BC Hydro's rules.
If you're installing this meter base in BC, you should follow BC Hydro’s requirement and ensure the electrician wires the load side accordingly.

Yes, the Hydel 320A meter socket on Evolt.ca is BC Hydro approved and includes a bypass feature.

If you remove the meter and engage the bypass, the house should still have power, assuming the bypass is a manual lever bypass (which temporarily maintains power during meter changes or maintenance).

However, there are a few key considerations:

Type of Bypass:

If it has a lever bypass, you can manually engage it to keep power flowing to the home.
If it's a horn bypass, you would need a jumper or special tool to complete the circuit.
If it’s an automatic bypass, it should maintain power temporarily when the meter is removed.
Utility Regulations:

BC Hydro may prohibit bypassing the meter without their approval. Tampering with the meter socket can be illegal and dangerous.
Engaging the bypass may also not be permanent—it’s usually designed for temporary use during meter servicing.
Safety Concerns:

Removing a meter while under load can cause arcing, which is dangerous.
Bypassing may not provide the same level of protection as the meter setup.
It is always best to consult with BC Hydro or a licensed electrician before attempting any modifications.
Would you like help finding a permanent backup power solution (e.g., a generator transfer switch) instead of relying on the bypass?

The Warning Label states that the bypass will not work if the meter is not fully hooked up. To switch it back to a meter connection you have have the meter installed and bypass cover must be closed before you install the meter ring.