- Edmonton Stock: 10
Teleduct 90° Bend · 2 in x 36 in Radius · Orange PVC DB2/Telecom Duct · Royal 93102
Orange PVC Teleduct 90° bend for 2 in underground telecom duct runs, with a 36 in sweep radius to help maintain cable pull geometry through directional changes. Commonly used in direct-buried communication duct systems; verify duct type, bend radius, and local code requirements before installation.
What this product is for
This 2 in Teleduct bend is used to change direction by 90° in underground communication and signal duct runs. It is an orange PVC long-sweep style bend intended for Teleduct/DBII-type installations where cable protection and smoother pulling paths are required.
Use for
Use for underground telecom duct banks, communication raceways, and other direct-buried low-voltage duct systems that require a 2 in trade size bend with a 36 in (914 mm) radius. The long sweep helps reduce pull resistance compared with tighter bends in typical cable routing applications.
Avoid for
Avoid using this bend where a different duct system, wall type, or bend radius is specified, or where a standard electrical conduit elbow is required instead of Teleduct/DBII duct fittings. Do not assume compatibility with every PVC duct system without confirming the matching product family and installation standard.
Best for
Best for contractors installing underground communications infrastructure who need a 90° directional change while maintaining a broad sweep for cable pulling. A 36 in (914 mm) radius is typically selected where gentler cable handling is preferred over tighter layout constraints.
Installed in
Installed in buried outdoor duct runs, site services, campus communication pathways, and utility or commercial underground raceway layouts. Commonly paired with orange Teleduct/DBII PVC duct in Canadian underground installations.
Why this product exists
This fitting provides a factory-formed 90° change in direction for 2 in duct runs, helping maintain consistent geometry and reducing field bending or improvised transitions. In practice, long-sweep bends are commonly chosen to support easier cable installation and lower pulling stress. Actual pulling performance depends on cable type, run length, lubrication, layout, and local electrical code.
Compared with similar products
Compared with a tighter 12 in or 24 in radius bend, a 36 in (914 mm) sweep generally offers a smoother path for cable pulls but requires more installation space. Compared with standard gray electrical PVC elbows, this orange Teleduct-style bend is intended for underground communication duct identification and matching system use.
Specifications
- Product type: Teleduct/DBII 90° bend
- Trade size: 2 in
- Bend radius: 36 in (914 mm)
- Angle: 90°
- Colour: Orange
- Material: PVC
- Application: Underground communication duct systems
- Brand: Royal / Westlake Pipe & Fittings
- Manufacturer part number: 93102
Minimum Order $20
We accept the following payment methods:
Credit Card can offer cardholders convenience, security, rewards, and the opportunity to build a healthy credit history.
Click here for Contractor Cash Account
Trade Credit is a standard financing option for contractors and construction companies to obtain supplies and keep their projects moving. We offer 30-day credit terms to trade contractors on approved applications only.
Click here for Contractor Credit Account 
(Contractor Accounts)
Standard Shipping-Free on orders over $249 in Metropolitan Areas / $499 in Rural Areas
(All Other Accounts)
Standard Shipping-Free on orders over $499
Minimum Order Is $20
Freight Surcharge Apply To Oversized/Over-Weight Items(Not Limited To):
- PVC and EMT Pipe
- Wire and Cable
- Items over 48 inches in length
Surcharges are applied to items on an individual basis regardless if the rest of the order meets prepaid levels. If a freight line appears at the time of check out it only applies to the Items carrying a surcharge and not the entire basket of goods.
Shipping Options:
- A courier can deliver to your home, office, or your job site
- Pick up at local depot near you (applies to the following locations)
Edmonton Warehouse 8135 Roper Rd Edmonton, T6E 6S4, AB
Burnaby Warehouse 5608 Goring St Burnaby, V5B 3A3, BC
Orders are typically delivered within two to eleven business days. The transit time begins the first full shipping day after your order leaves our warehouse. Please allow an additional 2-5 days for delivery to remote locations, additional fees may apply.
THE FOLLOWING APPLIES TO STANDARD SHIPPING OPTIONS
- We cannot deliver to P.O. boxes.
- A signature may be required for shipments over $500.
- No weekend delivery.
- Wire & cable, EMT or PVC conduit, tube lamps 4ft or greater, and 10ft ground rods & mast pipes have special conditions.
Standard Shipping cost on orders less than $499
Total shipping cost = "Per Shipment" cost + "Per Item" cost. The "per item" cost is listed in terms of price per pound.
Product Group | Per Shipment* | Per Item |
|---|---|---|
Boxes | $6.99 | $1.49/lb |
Conduit & Raceway | $149.99 | $2.49/lb |
Connectors & Fittings | $5.99 | $1.19/lb |
Data & Structured Home | $5.99 | $1.19/lb |
Distribution Equipment | $5.99 | $1.19/lb |
Emergency Lighting | $6.99 | $1.49/lb |
Heating & Ventilation | $6.99 | $1.49/lb |
Lighting Controls | $5.99 | $1.19/lb |
Lighting Indoor | $6.99 | $1.49/lb |
Lighting Outdoor | $6.99 | $1.49/lb |
Tools | $4.99 | $.99/lb |
Wire & Cable | $49.99 | $2.29/lb |
Wiring Devices | $5.99 | $1.19/lb |
Any combination of the above items | Highest applicable per-shipment charge | As above |
Effective Date: August, 15, 1998
At Evolt Electrical Supply, customer satisfaction is our top priority. Please review our return policy below:
Returns
Defective Items:
- If you receive a defective item, you may return it for a replacement or refund within 30 days of purchase.
- To initiate a return, please contact our customer service team with your order number and a description of the defect.
Non-Defective Items:
- We do not accept returns for non-defective items. All sales are final once the product is shipped or ordered from the manufacturer. In certain circumstances we may amend this so feel free to contact our customer service team.
Return Process
Authorization:
- Before returning any items, you must obtain a Return Merchandise Authorization (RMA) number from our customer service team. Returns without an RMA number will not be accepted.
- Backordered items can not be cancelled if the item is in transit from the manufacturer, contact us to review.
Shipping:
- Customers are responsible for the return shipping costs. We recommend using a trackable shipping service or purchasing shipping insurance.
Condition:
- Returned items must be in their original packaging and condition. Any items returned damaged due to improper packaging or misuse will not be eligible for a refund or replacement.
Refunds
- Once we receive and inspect your returned item, we will notify you of the approval or rejection of your refund.
- Approved refunds will be processed within [7] business days and a credit will automatically be applied to your original method of payment.
Related products
- Edmonton Stock: 5
Rigid PVC Duct Solvent Cement · 250 mL · EcoVOC Clear Formula · Royal RVOC250
RVOC250
22 – Loyalty RewardsTeleduct 90° Bend · 2 in · 24 in Radius · Orange PVC · Westlake Pipe & Fittings 93122
93122
Available to Order | Typically Arrives in 1 - 3 Weeks Ships from Abbotsford BC Factory29 – Loyalty RewardsDuct Coupling · 3 in · Solvent Weld PVC · White · Westlake Pipe & Fittings SWC03
SWC03
Available to Order | Typically Arrives in 1 - 3 Weeks Ships from Abbotsford BC Factory3 – Loyalty Rewards
