Octagonal aluminium back box · standard flange · for in-grade, wall, ceiling and stair installations · MP Lighting EBX-OCT1-CSMA
What this product is for
This octagonal aluminium back box is used as a rough-in housing for compatible MP Lighting recessed and in-grade luminaires and mounting kits. It provides the enclosure and mounting interface needed before the finished fixture is installed.
Use for
Use for ground, ceiling, wall and stair installations where the fixture schedule calls for MP Lighting OCT1 C-flange back box compatibility. It is suitable for wet, damp and dry locations.
Avoid for
Avoid using this back box where a different flange style, paving-stone flange, pipe version, or non-compatible fixture family is required. Confirm fixture and mounting kit compatibility before ordering.
Best for
Best for landscape and architectural lighting projects that need a manufacturer-matched rough-in component for in-grade or recessed installations. It is a practical choice when the box must be set during concrete, masonry or finish-stage coordination.
Installed in
Typically installed in grade, walls, ceilings and stair risers. The comparison sheets also indicate rebar-supported installation provisions, with a rebar hole sized at approximately 9/16 in (14 mm) and recommended rebar size of approximately 1/2 in / 10M, depending on the installation method and site conditions.
Why this product exists
This product allows the rough-in work to be completed before the luminaire is fitted, helping coordinate concrete, hardscape and finish trades. For many in-grade and recessed lighting jobs, using the correct manufacturer back box helps maintain fit, alignment and service access.
Compared with similar products
Compared with generic or third-party boxes, this MP Lighting back box is intended for specific OCT1-compatible applications and flange configurations. Compared with other MP Lighting OCT1 back boxes, the key buying detail here is the C-series standard flange configuration, so matching the exact part number to the fixture or mounting kit is important.
Specifications
- Product type: Octagonal back box
- Material: Aluminium back box
- Flange: Standard flange
- Application: In-grade, wall, ceiling and stair installations
- Location rating: Wet, damp and dry locations
- Approximate box diameter: 5-3/4 in (145 mm)
- Approximate body diameter: 4-1/8 in (106 mm)
- Rebar hole: approximately 9/16 in (14 mm)
- Typical recommended rebar size: 1/2 in (10M)
- Brand: MP Lighting
- Manufacturer part number: EBX-OCT1-CSMA
Compatibility should be confirmed against the fixture or mounting kit submittal. Actual installation requirements depend on fixture selection, substrate, drainage, layout and local electrical code.
Minimum Order $20
We accept the following payment methods:
Credit Card can offer cardholders convenience, security, rewards, and the opportunity to build a healthy credit history.
Click here for Contractor Cash Account
Trade Credit is a standard financing option for contractors and construction companies to obtain supplies and keep their projects moving. We offer 30-day credit terms to trade contractors on approved applications only.
Click here for Contractor Credit Account 
(Contractor Accounts)
Standard Shipping-Free on orders over $249 in Metropolitan Areas / $499 in Rural Areas
(All Other Accounts)
Standard Shipping-Free on orders over $499
Minimum Order Is $20
Freight Surcharge Apply To Oversized/Over-Weight Items(Not Limited To):
- PVC and EMT Pipe
- Wire and Cable
- Items over 48 inches in length
Surcharges are applied to items on an individual basis regardless if the rest of the order meets prepaid levels. If a freight line appears at the time of check out it only applies to the Items carrying a surcharge and not the entire basket of goods.
Shipping Options:
- A courier can deliver to your home, office, or your job site
- Pick up at local depot near you (applies to the following locations)
Edmonton Warehouse 8135 Roper Rd Edmonton, T6E 6S4, AB
Burnaby Warehouse 5608 Goring St Burnaby, V5B 3A3, BC
Orders are typically delivered within two to eleven business days. The transit time begins the first full shipping day after your order leaves our warehouse. Please allow an additional 2-5 days for delivery to remote locations, additional fees may apply.
THE FOLLOWING APPLIES TO STANDARD SHIPPING OPTIONS
- We cannot deliver to P.O. boxes.
- A signature may be required for shipments over $500.
- No weekend delivery.
- Wire & cable, EMT or PVC conduit, tube lamps 4ft or greater, and 10ft ground rods & mast pipes have special conditions.
Standard Shipping cost on orders less than $499
Total shipping cost = "Per Shipment" cost + "Per Item" cost. The "per item" cost is listed in terms of price per pound.
Product Group | Per Shipment* | Per Item |
|---|---|---|
Boxes | $6.99 | $1.49/lb |
Conduit & Raceway | $149.99 | $2.49/lb |
Connectors & Fittings | $5.99 | $1.19/lb |
Data & Structured Home | $5.99 | $1.19/lb |
Distribution Equipment | $5.99 | $1.19/lb |
Emergency Lighting | $6.99 | $1.49/lb |
Heating & Ventilation | $6.99 | $1.49/lb |
Lighting Controls | $5.99 | $1.19/lb |
Lighting Indoor | $6.99 | $1.49/lb |
Lighting Outdoor | $6.99 | $1.49/lb |
Tools | $4.99 | $.99/lb |
Wire & Cable | $49.99 | $2.29/lb |
Wiring Devices | $5.99 | $1.19/lb |
Any combination of the above items | Highest applicable per-shipment charge | As above |
Effective Date: August, 15, 1998
At Evolt Electrical Supply, customer satisfaction is our top priority. Please review our return policy below:
Returns
Defective Items:
- If you receive a defective item, you may return it for a replacement or refund within 30 days of purchase.
- To initiate a return, please contact our customer service team with your order number and a description of the defect.
Non-Defective Items:
- We do not accept returns for non-defective items. All sales are final once the product is shipped or ordered from the manufacturer. In certain circumstances we may amend this so feel free to contact our customer service team.
Return Process
Authorization:
- Before returning any items, you must obtain a Return Merchandise Authorization (RMA) number from our customer service team. Returns without an RMA number will not be accepted.
- Backordered items can not be cancelled if the item is in transit from the manufacturer, contact us to review.
Shipping:
- Customers are responsible for the return shipping costs. We recommend using a trackable shipping service or purchasing shipping insurance.
Condition:
- Returned items must be in their original packaging and condition. Any items returned damaged due to improper packaging or misuse will not be eligible for a refund or replacement.
Refunds
- Once we receive and inspect your returned item, we will notify you of the approval or rejection of your refund.
- Approved refunds will be processed within [7] business days and a credit will automatically be applied to your original method of payment.