Hole Saw · 6-1/4 in (159 mm) · Tri-Bore multi-purpose carbide teeth · IDEAL Industries 36-363
What this product is for
This 6-1/4 in (159 mm) IDEAL Tri-Bore hole saw is used to cut large-diameter openings in abrasive and mixed materials on electrical and mechanical rough-in work. It is part of the Tri-Bore multi-purpose hole saw range and is sized by IDEAL for 6 in duct applications.
Use for
Use for wood with nails, cement board, composite enclosures, ceiling tile and similar abrasive materials. It is suitable when electricians and contractors need a larger opening than a standard recessed-lighting saw, such as panel modifications, enclosure penetrations or duct-related cutouts where the material matches the manufacturer guidance.
Avoid for
Avoid using this listing as a general-purpose bi-metal hole saw for thick steel or stainless applications unless the material and setup are confirmed for the tool. Also avoid ordering it alone if you do not already have the correct Tri-Bore arbor and pilot, because the hole saw requires IDEAL arbor 35-394 and a compatible pilot bit.
Best for
Best for electricians, HVAC installers and maintenance teams cutting larger openings in abrasive board products or nail-embedded wood where carbide teeth are preferred over standard bi-metal teeth. A practical buying point is that this size is commonly selected for 6 in duct openings.
Installed in
Typically used on site in commercial fit-outs, residential renovations, service work, mechanical rooms, utility spaces and prefabricated enclosure work. Actual cut quality depends on drill torque, material support, feed pressure and pilot selection.
Why this product exists
Large-diameter cuts in cement board, composite materials and wood with embedded nails can wear out standard hole saws quickly. The Tri-Bore design uses carbide teeth, deep angled gullets for plug removal and a deep-cup format intended for these tougher cutting tasks.
Compared with similar products
Compared with a standard bi-metal hole saw, this Tri-Bore model is intended for more abrasive materials and nail-containing wood. Compared with knockout methods in cement board or composite enclosures, it is designed to produce a cleaner round opening. As typical trade guidance, carbide hole saws are often chosen when material mix is uncertain, but actual life depends on speed, pressure, backing and debris clearance.
Typical guidance only. Actual performance depends on installation conditions, material composition, drill speed and operator technique.
Specifications
- Manufacturer: IDEAL Industries
- Manufacturer part number: 36-363
- Product family: Tri-Bore
- Product type: Multi-purpose hole saw
- Hole saw diameter: 6-1/4 in (159 mm)
- Application reference: 6 in duct
- Cutting edge: Carbide teeth
- Suitable materials: Wood with nails, cement board, composite enclosures, ceiling tile
- Arbor required: IDEAL 35-394
- Pilot options sold separately: IDEAL 36-367 spade bit for wood; IDEAL 36-368 carbide pilot for abrasive materials
- Design notes: Deep angled gullets for plug removal; rugged construction; deep-cup design
Minimum Order $20
We accept the following payment methods:
Credit Card can offer cardholders convenience, security, rewards, and the opportunity to build a healthy credit history.
Click here for Contractor Cash Account
Trade Credit is a standard financing option for contractors and construction companies to obtain supplies and keep their projects moving. We offer 30-day credit terms to trade contractors on approved applications only.
Click here for Contractor Credit Account 
(Contractor Accounts)
Standard Shipping-Free on orders over $249 in Metropolitan Areas / $499 in Rural Areas
(All Other Accounts)
Standard Shipping-Free on orders over $499
Minimum Order Is $20
Freight Surcharge Apply To Oversized/Over-Weight Items(Not Limited To):
- PVC and EMT Pipe
- Wire and Cable
- Items over 48 inches in length
Surcharges are applied to items on an individual basis regardless if the rest of the order meets prepaid levels. If a freight line appears at the time of check out it only applies to the Items carrying a surcharge and not the entire basket of goods.
Shipping Options:
- A courier can deliver to your home, office, or your job site
- Pick up at local depot near you (applies to the following locations)
Edmonton Warehouse 8135 Roper Rd Edmonton, T6E 6S4, AB
Burnaby Warehouse 5608 Goring St Burnaby, V5B 3A3, BC
Orders are typically delivered within two to eleven business days. The transit time begins the first full shipping day after your order leaves our warehouse. Please allow an additional 2-5 days for delivery to remote locations, additional fees may apply.
THE FOLLOWING APPLIES TO STANDARD SHIPPING OPTIONS
- We cannot deliver to P.O. boxes.
- A signature may be required for shipments over $500.
- No weekend delivery.
- Wire & cable, EMT or PVC conduit, tube lamps 4ft or greater, and 10ft ground rods & mast pipes have special conditions.
Standard Shipping cost on orders less than $499
Total shipping cost = "Per Shipment" cost + "Per Item" cost. The "per item" cost is listed in terms of price per pound.
Product Group | Per Shipment* | Per Item |
|---|---|---|
Boxes | $6.99 | $1.49/lb |
Conduit & Raceway | $149.99 | $2.49/lb |
Connectors & Fittings | $5.99 | $1.19/lb |
Data & Structured Home | $5.99 | $1.19/lb |
Distribution Equipment | $5.99 | $1.19/lb |
Emergency Lighting | $6.99 | $1.49/lb |
Heating & Ventilation | $6.99 | $1.49/lb |
Lighting Controls | $5.99 | $1.19/lb |
Lighting Indoor | $6.99 | $1.49/lb |
Lighting Outdoor | $6.99 | $1.49/lb |
Tools | $4.99 | $.99/lb |
Wire & Cable | $49.99 | $2.29/lb |
Wiring Devices | $5.99 | $1.19/lb |
Any combination of the above items | Highest applicable per-shipment charge | As above |
Effective Date: August, 15, 1998
At Evolt Electrical Supply, customer satisfaction is our top priority. Please review our return policy below:
Returns
Defective Items:
- If you receive a defective item, you may return it for a replacement or refund within 30 days of purchase.
- To initiate a return, please contact our customer service team with your order number and a description of the defect.
Non-Defective Items:
- We do not accept returns for non-defective items. All sales are final once the product is shipped or ordered from the manufacturer. In certain circumstances we may amend this so feel free to contact our customer service team.
Return Process
Authorization:
- Before returning any items, you must obtain a Return Merchandise Authorization (RMA) number from our customer service team. Returns without an RMA number will not be accepted.
- Backordered items can not be cancelled if the item is in transit from the manufacturer, contact us to review.
Shipping:
- Customers are responsible for the return shipping costs. We recommend using a trackable shipping service or purchasing shipping insurance.
Condition:
- Returned items must be in their original packaging and condition. Any items returned damaged due to improper packaging or misuse will not be eligible for a refund or replacement.
Refunds
- Once we receive and inspect your returned item, we will notify you of the approval or rejection of your refund.
- Approved refunds will be processed within [7] business days and a credit will automatically be applied to your original method of payment.